Access Control Sales Ltd
LARGE DIGITAL LED TIMERS & TOTALISERS DISPLAYS
Our range of Large Digital LED Timers and Totalisers offer many options. All Timers have a Time base in Hours, Minutes, Seconds and combinations. We can also offer Long Range Timers also with Years, Weeks and Days. Typical functions are UP or DOWN timing, Totalising or Batch timing, TAKT timing, Repeat Cycle, One Shot output. Alarm trips and re-transmission or direct Serial Input.

INPUT SIGNALS – CONTACT CLOSURE, NPN, PNP, 24V PLC
LED NUMERICAL DISPLAY OF
HRS : MINS : SECS, HRS : MINS, MINS : SECS, MINS, SECS, 1/10 SEC
INDOOR or OUTDOOR USE
Numerical LARGE DIGITAL LED TIMERS & TOTALISERS – General Overview
These Large Digital LED Timers and Totalisers are ideal for all Industrial and Commercial applications ( such as Sports Halls and Sporting events outdoors ) with the following functions available.
Time UP, Time Down, Repeat Cycle, TAKT Timing, Stop Watch.
INPUT
- Contact Closure
- NPN
- PNP
- 24V PLC
OUTPUT ( Options )
- Relay Output at Zero or at UP Time out
- Output at various points ( settable ) during Time UP or DOWN
TIME BASE RANGES
- Secs ( 1/10 sec option )
- Mins
- Mins : Secs
- Hrs : Mins
- Hrs : Mins : Secs
- DAYS : Hrs : Mins ; Secs
ALL THE ABOVE LEGENDS / SYMBOLS ARE SUPPLIED ON REQUEST – AT NO CHARGE
FUNCTIONS
- To a SET POINT from Zero or FREE RUNNING to MAXIMUM SCALE
- From a SET POINT to Zero
- Stop Watch ( Start / Stop / Reset )
LED DISPLAY DIGITS
- 2, 3, 4, 5 or 6
LARGE DISPLAY CONTROL INPUT OPTIONS
- Remote wiring for START / STOP / RESET
- Remote Plug-in Box for setting Time value, Start / Stop / Reset
- IR Remote
LARGE LED TIMERS – APPLICATIONS
The use of these Timers is very wide, applications include:
- Measuring assembly line down time.
- Controlling a process or event by Time alone.
- Calculating process efficiency.
- Measuring Time taken for line changeovers.
- Measuring TAKT Time.
- Measuring a total event or process Time.
- Improving employee motivation.
- Sports Time events …etc.
ANYTHING THAT CAN BE MEASURED IN RELATION TO TIME
LARGE DISPLAY LINES
The Large LED Timers can be supplied in SINGLE LINE or MULTILINE format and the Multiline displays can be a mix of Time Bases.
Examples of Single and Multiline Timers with Different Time Ranges


LARGE DIGIT LED TIMER – DESCRIPTIONS And Uses
Up or Down Timers ( And TAKT Time }
UP TIMERS can also be called TIME TOTALISERS, whereby an INPUT START SIGNAL initiates the Timing UP from Zero to a PRESET VALUE or continues to TIME UP until the maximum scale range is reached, In both cases an OUTPUT SIGNAL can be provided.

DOWN TIMERS/ TAKT TIME can also be called BATCH TIMERS, whereby a PRESET VALUE is set for a period of Time that an event has to take place. When that Time is reached, normally at Zero an OUTPUT SIGNAL can be provided.
This is typical of TAKT TIMING, where an operation must be completed within a set time.
Our Timers can, at ZERO, in such circumstances show NEGATIVE TIME and even the LEDs can change colour to show the SET TIME has been exceeded.
STOP WATCH
This functions as its name suggests as a STOP WATCH, for INDUSTRIAL or SPORTS events in particular, where the Time needs to be STARTED and STOPPED and RECORDED and either RESET or continues to TIME.
These are usually UP TIMERS.
These functions can be manually controlled or through SERIAL communication.


Totalisers
TOTALISERS are dedicated to the task of displaying TIME ELAPSED and are usually UP TIMERS.
They ( like all the previously described Timers ) are available in all the Time Bases listed earlier and are usually used to display Time only with no OUTPUT function.
Many of these type of Timers are used to display POWER USEAGE like ‘ kWh ‘ or similar.
They accumulate rather than simply display usage.
Day Timers
DAYS TIMERS are LONG RANGE Timers, usually UP TIMING from Zero and invariable used with HRS : MINS and sometimes SECS.
They can also be used a DOWN TIMERS where a set number of DAYS is entered remotely and when the Timer receives a START SIGNAL INPUT, will start Timing Down and every 24 hours the DAYS will decrease by one.
In both cases these Timers are used to show the Time elapsed before an EVENT takes place or the Time left before an EVENT takes place.
LARGE DIGIT LED Timers HEIGHT OPTIONS
All these Timers are available in the following LED DIGIT sizes:
2.3” (58mm), 4” (102mm), 6” (150mm), 8” (200mm), 12” (305mm), 16” (410mm), 18” (457mm).
Larger digits are available depending on quantity.
VIEWING DISTANCES FOR LARGE DIGIT TIMERS AND TOTALISERS
The maximum viewing distances for the DIGIT SIZES given below are based on the LED manufacturers specifications and give CLEAR UNAMBIGUOUS READING. They are NOT to be taken MAXIMUM distances and normally viewing distance will be less than the maximum figure given.
DIGIT HEIGHTS | VIEWING DISTANCES |
---|---|
Actual | Guide Only |
2.3” (58mm) | 15 meters / 50 feet |
4” (102mm) | 35 meters / 115 feet |
6” (150mm) | 55 meters / 180 feet |
8” (203mm) | 75 meters / 246 feet |
12” (305mm) | 115 meters / 377 feet |
14″ (355mm) | 135 meters /442 feet |
16” (400mm) | 155 meters / 508 feet |
18″ (457 mm) | 170 metres / 557 feet |
HIGH BRIGHTNESS DAYLIGHT VIEWING LEDS
High brightness LEDs are used for OUTDOOR applications but can also be used for INDOOR environments where it might be murky to ensure visibility at all times.
LARGE LED TIMERS – REMOTE BOX OPTIONS / IR REMOTE
The Large Digit Timers can be set for TIME, START / STOP / RESET and OUTPUT functions.
The Remote Boxes are plug-in via a 5 meter cable and ‘ D ‘ type connector or they can be controlled with an IR Remote. The plug-in Remote Boxes can be hand held or fixed to a Wall / Surface, whereas the IR Remote is purely hand held with a 10 meter send and receive operating distance.
MOUNTING OPTIONS for LARGE DIGITAL LED Timer DISPLAYS
THREE models are available, Wall, Panel and Suspension.
WALL MOUNT
All Wall mounting displays have adjustable Tilt side brackets up to 8” ( 203mm ) SINGLE LINE, thereafter they have welded ‘ L ‘ shaped fixed corner brackets ( top and bottom ).
SUSPENSION MOUNT
Suspension mounting is usually used for Double Sided Displays, Large Digits and / or Multiline. To be viewed from a distance by a number of work staff in an area where common information is required. These displays can have a variety of different inputs as well as time.

LARGE DIGITAL LED TIMERS – GENERAL SPECIFICATIONS
- Control commands START / STOP / RESET
- Volt Free Momentary contact closure
- Number of digits available 2, 3, 4, 5, 6 for UP / DOWN / STOP WATCH Timers
- Number of digits available 6, 7, 8 or 9 for DAYS Timers
BATTERY BACK UP
Standard on all Timers
IP / NEMA RATINGS
- IP54 / NEMA 3, 13 for Indoor use
- IP65 / NEMA 4 (4X) for Outdoor use
INPUT POWER SUPPLIES
- 95~265Vac
- 24Vdc
- 12Vdc
CONTROL INPUT OPTIONS
- Contact Closure
- NPN
- PNP
- 24V PLC
- RS-232, RS-485
- MODBUS
CONTROL OUTPUTS
- Alarm Setting ( Relay )
- RS-485
ACCURACY
- 01% of range
OPERATING ENVIRONMENT
10 ~ +50 °C / 14 ~ 122 °F
Specification Sheets
Our specification sheets provide you with all the information contained on this web page in a PDF printable form.
To download a specification sheet complete the CONTACT FORM below and if you tick the box requesting a specification sheet then you will be directed to the downloads page.
How Can We Help?
Whatever your Large Digit LED Display requirements are we are sure we can help. Contact Us Now for further information.
To help us provide a realistic quotation we will need as much of the following information as possible.
DIGIT HEIGHT 2.3”, 4.0”, 6.0”, 8.0”, 12.0”, 14.0”, 16.0”, 18.0”
NUMBER OF DIGITS 2, 3, 4, 5, 6
FUNCTION Time UP, Time DOWN, Repeat Cycle, TAKT Timing, Stop Watch or Days
NUMBER OF LINES Single Line or Multi Line
INPUT TYPE Contact closure, NPN, PNP, 24V PLC
OUTPUT OPTIONS Relay Output at ZERO ( DOWN Timing ), Relay Output at TIME OUT ( UP Timing )
SCALE RANGE
- Secs ( 1/10 sec option )
- Mins
- Mins : Secs
- Hrs : Mins
- Hrs : Mins : Secs
- DAYS : Hrs : Mins : Secs
LEGENDS PLEASE SPECIFY
REMOTE OPTIONS Plug-in remote box or IR remote
MOUNTING TYPE Wall, Panel or Suspension
Contact Form – Timers and Totalisers
"*" indicates required fields